Metric Halo Discussion Forum: MIOConsole » Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X)

Home

Help

Home » Hardware » MIOConsole » Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X)

Show: Today's Messages :: Show Polls :: Message Navigator

Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86564]

Wed, 13 September 2017 03:14

Djooh
Messages: 4
Registered: September 2017
Location: France

Junior Member

Hello everyone,

First of all, sorry I'm not English so I'll try to do my best for explaning the situation, thank you guys Razz

I have a Kemper Profiler and try to configurate the Mio Console for reamping in Logic Pro X, but I fail since few days and I don't know how to do anymore. I connected 2 spdif cables from the Kemper IN and OUT to my ULN2 OUT and IN. I record a DI track in the DAW, for that no problem, the problem come when I want to reamp, I have to change the output from my DI track in the DAW, but nothing change, so here some pictures off my Mio console configuration. The ULN2 should be slave of the Kemper.

index.php?t=getfile&id=128&private=0

I don't know if it's clear for you to understand, let me know what is wrong on my setup, thank you very much in advance.

Cheers Very Happy

Attachment: Capture d’écran 2017-09-07 à 14.29.48.png
(Size: 406.09KB, Downloaded 2152 times)
Attachment: Capture d’écran 2017-09-08 à 16.07.33.png
(Size: 123.98KB, Downloaded 2240 times)

Report message to a moderator

Re: Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86568 is a reply to message #86564]

Thu, 14 September 2017 14:23

bj
Messages: 621
Registered: July 2011

Senior Member
Administrator

You need to route a direct out from the DAW 1/2 to the Digital 1/2 output so that your recorded signal can be sent to the amp; then the digital signal from the amp will come back on FW3+4

Report message to a moderator

Re: Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86570 is a reply to message #86568]

Fri, 15 September 2017 13:51

Djooh
Messages: 4
Registered: September 2017
Location: France

Junior Member

Hi bj, thank you very much. But on the right of the Mio console (system, clock source, etc...), the parameters are good ?

Report message to a moderator

Re: Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86571 is a reply to message #86570]

Fri, 15 September 2017 14:17

bj
Messages: 621
Registered: July 2011

Senior Member
Administrator

Those settings are fine, as long as you are planning on clocking the Kemper from the 2882 via SPDIF. If the Kemper is also on internal clock, then you will get clicks. One of the devices needs to have it clock derived from the digital input. It doesn't really matter which one.

Report message to a moderator

Re: Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86572 is a reply to message #86571]

Fri, 15 September 2017 15:05

Djooh
Messages: 4
Registered: September 2017
Location: France

Junior Member

Ok thank you very much, I'll try that tomorrow Smile

Report message to a moderator

Re: Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86573 is a reply to message #86572]

Sat, 16 September 2017 04:04

Djooh
Messages: 4
Registered: September 2017
Location: France

Junior Member

Hi, so that doesn't work, there is a big buzz, here a picture, I tried different options but the buzz stay :

index.php?t=getfile&id=130&private=0

Attachment: Capture d’écran 2017-09-16 à 10.00.00.png
(Size: 56.29KB, Downloaded 1971 times)

Report message to a moderator

Re: Spdif configuration for reamping... (ULN2, Kemper, Logic Pro X) [message #86579 is a reply to message #86573]

Mon, 18 September 2017 14:50

bj
Messages: 621
Registered: July 2011

Senior Member
Administrator

You may have set up a feedback loop. If the FW3 or FW4 input in Logic is routed to the main mix, you will have a feedback loop.

It would probably be best for you to open a support ticket:

http://mhsecure.com/support

[Updated on: Mon, 18 September 2017 14:54]

Report message to a moderator

Previous Topic:	Console and Output crashes constantly
Next Topic:	Monitor Control

Goto Forum:

-=] Back to Top [=-

[

]

Current Time: Sun May 28 01:42:58 EDT 2023