Metric Halo Discussion Forum
The place to talk MH!
Home   Search      Help    Register    Login
Home » Hardware » MIOConsole » RME ARC USB for controlling monitor
RME ARC USB for controlling monitor [message #88263] Sat, 30 April 2022 13:08 Go to next message
mxmln is currently offline  mxmln
Messages: 6
Registered: April 2022
Location: Vienna AUT
Junior Member
Hi,


I am testing a LIO-8 interface one of my colleagues borrowed to me and i am slowly but steadily getting acquainted with the device and its software.
So far I am very excited and planning on purchasing a metric halo interface myself.

There is one question in particular: as I have been working with RME using an ARC USB remote as a physical monitor controller, it there any way to map it or any comparable device to MIOConsole's monitor controller? I tried to find an answer myself on metric halo's homepage and the manual but might have glossed over it.


Kind regards,
Walch Maximilian

Report message to a moderator

Re: RME ARC USB for controlling monitor [message #88266 is a reply to message #88263] Sat, 30 April 2022 14:37 Go to previous messageGo to next message
henningaround is currently offline  henningaround
Messages: 10
Registered: January 2022
Location: Cologne
Junior Member
afaik there is no hardware remote controller. I use an Elgato Stream Deck with the keystrokes that com with MIOConsole3d. It's not reliable and often doesn't work. It's bad not to have a decent hardware remote for such a nice interface.

Report message to a moderator

Re: RME ARC USB for controlling monitor [message #88268 is a reply to message #88266] Sat, 30 April 2022 18:19 Go to previous messageGo to next message
mxmln is currently offline  mxmln
Messages: 6
Registered: April 2022
Location: Vienna AUT
Junior Member
ok - i will look into it a little more. when opening the control surface settings i can choose the ARC USB at least.
maybe i can get it to work via MCP.

Report message to a moderator

Re: RME ARC USB for controlling monitor [message #88270 is a reply to message #88268] Sun, 01 May 2022 01:18 Go to previous messageGo to next message
henningaround is currently offline  henningaround
Messages: 10
Registered: January 2022
Location: Cologne
Junior Member
Well I should say you can use Mackie Control or EuControl enabled controllers for this. However there is no device that I know that really has a monitor section that gives you enough knob per function top fully rely on it.

Report message to a moderator

Re: RME ARC USB for controlling monitor [message #88272 is a reply to message #88270] Tue, 03 May 2022 09:14 Go to previous messageGo to next message
mxmln is currently offline  mxmln
Messages: 6
Registered: April 2022
Location: Vienna AUT
Junior Member
that's a bummer - maybe i'll be able to program sth
i'll post again as soon as i've figured something out

Report message to a moderator

Re: RME ARC USB for controlling monitor [message #88275 is a reply to message #88272] Wed, 04 May 2022 17:29 Go to previous message
henningaround is currently offline  henningaround
Messages: 10
Registered: January 2022
Location: Cologne
Junior Member
What I found out today using Bome MIDI Translator Pro are some MIDI Notes you can program to use with the mixer. I'm still not allowed to post any url here (I have a google sheet for that) so I give a short version here. Channel 1 Note 0-7 for Record Enable Channel 1-7, 8-15 for Solo, 16-23 for Mute, 24-31 for Select, 32-39 for Phase Invert, 40/41 Bank Left/Right, 42/43 Nudge Left/Right, 54-61 Monitor Source 1-8, 62-69 Monitor Destination 1-8, Note 74 Mono, Note 77 Mute, Note 78 Dim.
Maybe guys at Metric Halo could provide a full sheet?

Report message to a moderator

Previous Topic: Using a USB "Big Knob" for contolling MIO´s "Monitor Controller" (?)
Next Topic: Guide Setting up 2 x 2882 - 1 Master (FW), and 1 slave (ADAT)
Goto Forum:
  

[ PDF ]

Current Time: Mon Aug 15 03:40:14 EDT 2022